Search Results

This paper presents a validation method for indoor testing of a passenger car suspension. A study was done to design a supporting modular structure with comparable inertances with respect to a vehicle's actual suspension and body connection points. For the indoor test, the rear axle is positioned on a rotating drum. The suspension system is excited as the wheel passes over cleats fixed on the drum and transient wheel motions are recorded. The indoor test rig outputs (i.e., wheel and chassis accelerations) were compared with experimental data measured on an actual vehicle running at different speeds on the same set of cleats along a flat road. The comparison results validate the indoor testing method. The forces and moments acting at each suspension and chassis connection point were measured with a set of patented six-axis load cells. The forces, moments, wheel and subframe accelerations were measured up to 120 Hz.

The primary objective of the research discussed here was to compare the commercial computational fluid dynamics (CFD) software, CONVERGE, and a prevalent open-source code, OpenFOAM, with regard to their ability to predict spray and combustion characteristics. The high-fidelity data were obtained from the Engine Combustion Network (ECN) at Sandia National Laboratory in a constant-volume combustion vessel under well-defined, controlled conditions. The experiments and simulations were performed by using two diesel surrogate fuels (i.e., n-heptane and n-dodecane) under both non-reacting and reacting conditions. Specifically, ECN data on spray penetration, liquid length, vapor penetration, mixture fraction, ignition delay, and flame lift-off length (LOL) were used to validate both codes. Results indicate that both codes can predict the above experimental characteristics very well.

Direct-injection technology represents today a very interesting solution to the typical problems that are generally encountered in SI, gas-fueled engines such as reduced volumetric efficiency, backfire and knock. However, development of suitable injection systems and combustion chamber geometry is necessary to optimize the fuel-air mixing and combustion processes. To this end, CFD models are widely applied even if the influence of the mesh structure, numerical and turbulence models on the computed results are still matter of investigation. In this work, a numerical methodology for the simulation of the gas exchange and injection processes in gas-fueled engines was developed within the Lib-ICE framework, which is a set of libraries and applications for IC engine modeling developed using the OpenFOAM® technology. The gas exchange and fuel injection processes were simulated into a four-valve, pent-roof hydrogen-fueled engine with optical access.

The OpenFOAM® CFD methodology is nowadays employed for simulation in internal combustion engines and a lot of work has been done for an appropriate description of all complex phenomena. At the moment in the RANS turbulence models available in the OpenFOAM® toolbox the turbulence modulation is not yet included, and the present work analyzes the predictive capabilities of the code in simulating high injection pressure fuel sprays after modeling the influence of the dispersed phase on the turbulence structure. Different experiments were employed for the validation. At first, non-evaporating diesel spray was considered in a constant volume and quiescent vessel. The validation was performed via the available experimental spray evolution in terms of penetrations and spatial/temporal fuel distributions. Then the Sandia combustion chamber was chosen for diesel spray simulation in non-reacting conditions.

Tire-road interaction is one of the main concerns in the design of control strategies for active/semi-active differentials oriented to improve handling performances of a vehicle. In particular, the knowledge of the friction coefficient at the tire-road interface is crucial for achieving the best performance in any working condition. State observers and estimators have been developed at the purpose, based on the measurements traditionally carried out on board vehicle (steer angle, lateral acceleration, yaw rate, wheels speed). However, until today, the problem of tire-road friction coefficient estimation (and especially of its maximum value) has not completely been solved. Thus, active control systems developed so far rely on a driver manual selection of the road adherence condition (anyway characterized by a rough and imprecise quality) or on a conservative tuning of the control logic in order to ensure vehicle safety among different tire-road friction coefficients.

In the most elementary treatment of plane-wave reflection at the open end of a duct system, it is often assumed that the ends are pressure nodes. This implies that pressure is assumed as a constant at the open end termination and that steady flow boundary condition is supposed as instantaneously established. While this simplifying assumption seems reasonable, it does not consider any radiation of acoustic energy from the duct into the surrounding free space; hence, an error in the estimation of the effects of the flow on the acoustical response of an open-end duct occurs. If radiation is accounted, a complicated three-dimensional wave pattern near the duct end is established, which tends to readjust the exit pressure to its steady-flow level. This adjustment process is continually modified by further incident waves, so that the effective instantaneous boundary conditions which determine the reflected waves depend on the flow history.

A test rig (named RuotaVia) is presented for the in-door testing of road vehicle suspension systems. It is basically a drum (ϕ 2.6 m) providing a running surface for testing the dynamic performance of a single tire or suspension system (corner). The suspension system is instrumented for the measurement of the forces and the moments acting at each joint connecting the suspension to the car body. A new 6 axis load cell was designed and manufactured for this purpose. The accelerations in various locations of the system (wheel carrier, suspension arms, …) and the wheel centre displacements in the longitudinal and vertical directions are monitored. The effect of the dynamic interaction between the test rig and the suspension system is discussed in the paper. The direct measurement of the forces and moments at the suspension-chassis joints is still an effective way for understanding the vibration and harshness (VH) suspension performances.

The most common automotive drivelines transmit the engine torque to the driven axle through a differential. Semi-active versions of this device ([4], [5], [6]) have been recently conceived to improve vehicle handling at limit and under particular conditions; these differentials are based on the structural scheme of the passive one but they try to manipulate the vehicle dynamics by controlling the distribution of the driving torque on the wheels of the same axle thus generating a yaw moment. Unfortunately a semi-active differential is not able to perform a complete yaw control since the torque can only be transferred from the faster wheel to the slower one; on the other hand, active differentials ([11], [12], [13]) allow to generate the most appropriate yaw moment controlling both the amount of transferred torque and its direction.

The paper presents a new test rig (named RuotaVia) composed basically by a drum (2,6 m diameter), providing a running contact surface for vehicle wheels. A number of measurements on either full vehicles or vehicle sub-systems (single suspension system or single tyre) can be performed. Tire characteristics influencing rollover can be assessed. The steady-state maximum loads are as follows: Radial: 100kN, tangential: 100kN, lateral (axial with respect to the drum): 100kN. The superstructure carrying a measuring hub can excite the wheel under test up to 20 Hz in lateral and vertical directions. The steer angle range is ± 25 deg, the camber range is ± 80 deg. The minimum eigenfrequency of the drum is higher than 90 Hz and its maximum tangential speed is 440 km/h.